Inspects mechanical final assembly installations of the aircraft such as fuselage, wings, flaps, landing gears, and tail assemblies. Inspects systems such as hydraulic, pneumatic, oil, heat, and brakes. Visually and physically inspects electrical installations. Rechecks work after adjustment or repa

Final Assembly Inspector 2

Hi-Tek Professionals, Inc. • 
Palmdale, California, USA
Position Type: Contractor
Share
Job Description:

Inspects mechanical final assembly installations of the aircraft such as fuselage, wings, flaps, landing gears, and tail assemblies. Inspects systems such as hydraulic, pneumatic, oil, heat, and brakes. Visually and physically inspects electrical installations. Rechecks work after adjustment or repair. May monitor and verify quality in accordance with statistical process or other control procedures. Maintains necessary inspection logs and writes inspection reports. Candidate must understand aircraft structures.

Responsibilities include:

• Visually and physically inspect aircraft center fuselage structure, system and electrical installations for conformance to engineering requirements using a variety of precision measurement equipment and inspection tools to include micrometers, calipers, ball gages, flashlights, mirrors, ohm meters, laser gauges and depth gages.
• Structure inspections include location, gap verification, shim installation, hole drilling, fastener installation, sealing and coatings.
• System installations include tube, hose, valve, fastener installation, sealing and coatings common to hydraulic, pneumatic and fuel systems.
• Electrical installations include route, clamping, string tie, connector mating, pin insertion, crimping and coatings.
• Locate, identify and accurately document nonconforming product/material at time of discovery per applicable procedures.
• Visually and physically inspect rework and repair for compliance per engineering requirements.
• Mentor technicians on nonconforming product/material discovered during inspection to include engineering requirements, how to identify the nonconformance and process improvement.
• Develop, promote, and maintain collaborative team environment with fellow inspectors, support organizations and customers.
• Work well as part of a team and individually to increase quality, efficiency, effectiveness and affordability through process improvement and other quality control methods.
• Must be able to pass formal classroom training to include but not limited to hole drilling, sealing, countersinking, and fastener installation.
• Must be able to certify for half and full face respirator

Job Requirements:

Basic Qualifications:

• High School Diploma plus 4 years relevant mechanical and or inspection work experience.
• Must have experienced familiarity with inspection tools
• Must be willing to work any shift, overtime or non-standard work schedule.
• Must be able to work around composites, epoxies, and sealants for long periods of time.
• Must be technically proficient in Microsoft Office Suite to include but not limited to Word, Excel, Power Point and Outlook.
• Must be able to perform moderately strenuous physical and repetitious work to include climbing, bending, crawling, stooping, and kneeling, lifting, working with arms overhead, leaning and laying.
• Must be able to lift, grip, push, pull and hold 25+ pounds.
• Must be able to work in and around confined spaces to include but not limited to fuel tanks 
and ducts.
• Must be able to push and pull own body weight to enter and exit confined spaces.

 

1. What is the intended job duration for this requisition? 6 Months- 12 months
a. Will this be temporary or is there an opportunity to go permanent with the 
role? There is opportunity to become permanent.
2. What are the hard skills required for this role? Structures inspection
a. Are any of these skills interchangeable? Yes
b. What are the “nice to have” skills? Engineering Disposition Skills
3. Can this position be done remotely? No
4. Are there any other job titles/industries that seem to transition well into this role? 
Quality engineer, Manufacturing engineer, Inspector
5. What work schedule with the contractor be working: 4/10’s shift. Monday –
Thursday
 5/40, 9/80 or 4/10:
 Hours: 40 hours plus optional 30 hours of OT

Salary Range: Open-Open
Share
(Job and company information not to be copied, shared, scraped, or otherwise disseminated/distributed without explicit consent of JSfirm, LLC)

JSfirm, LLC

Roanoke, TX

jobs@jsfirm.com

JSfirm LLC, Privacy Policy

All rights reserved. 2001-2022 JSfirm